?

新葡亰496net

澳门新葡亰官网热线:www.146.net

?

首页

资讯动态

您所在的位置: 雷蒙磨 > 资讯动态 >

蒙磨粉电压不稳会对机器造成哪些危害

文章编辑:admin澳门新葡亰手机版:2016-11-16浏览次数:

0
雷蒙磨机主机电流高是什么原因?主机电流高对磨机有什么影响?许多客户在使用磨粉机设备的时候会遇到各种各样的问题,对于主机电流升高可能许多用户都会认为是电机原因,其实不然,下面由力迈机械专业的技术人员给大家讲解一下这其中的原因吧。
The host of Raymond mill current high is what reason? What is the effect of the high current on the mill? Many customers will encounter a variety of time in the use of mill equipment problems, the current increase may for the host many users will think is the motor reason, in fact, following by the technical staff and machinery to explain the reason.
雷蒙磨
雷蒙磨粉机主机电流高的原因
The reason of high current host Raymond Mill
一、物料难磨是主要原因。1、物料物料给的过于多,造成了雷蒙磨设备超负荷的运行,同时电耗增大,造成了主机电流升高,机体温度也会随之增高,并伴随着磨腔物料堵塞;2、物料自身的原因,物料的温度过高,会造成磨粉机电流的回升,让磨机温度升高;3、物料湿度过于高,造成磨机物料堵塞,使雷蒙磨碾磨困难造成电流回升。
One, material is difficult to wear is the main reason. 1, the material material to too much, resulting in equipment overload operation of Raymond mill, while energy consumption increases, causing the current increase in host body temperature, also can be increased, and accompanied by the grinding cavity material blockage; 2 reasons, the material itself, the material temperature is too high, will cause the rise of mill current so, mill temperature increased; 3, the material humidity too high, resulting in mill material blockage, the difficulties caused by the current rise of Raymond Mill grinding.
二、选粉机转速设定问题,选粉机转速设定偏高也会引起主机电流升高。
Two, the selection of the powder machine speed setting, the selection of the high speed of the powder machine can also cause the current increase in the host.
三、磨盘和磨辊磨损过于严重,或者间隙设置不当,间隙过小也会造成主机电流升高,让雷蒙磨运行困难。
Three, the grinding disc and the grinding roller wear too serious, or clearance is set properly, the gap is too small will cause the current increase in the host, let the Raymond mill operating difficulties.
主机电流高对雷蒙磨粉机的影响
Effect of high current host Raymond Mill
主机电流升高往往会伴随着风机电机的电流也升高,此时风力减小,吹不起物料,长期下来会引起物料堵塞,不仅影响雷蒙磨产量,严重的还会造成磨机的损坏,影响非常严重。
The current increase in the host is often accompanied by the current fan motor is increased, when the wind is reduced, blowing up material, come down for a long time will cause the material blockage, not only affect the output of Raymond mill, but also caused serious damage to the mill, very serious influence.
雷蒙磨主机电流升高的解决方法
Solution the host current increase of Raymond Mill
一、物料方面:要严格的控制进料量和进料的温度,保持均匀的给料,同时还要降低物料的湿度,雷蒙磨能粉磨的物料湿度必须在6%以下,过于湿的物料会引起粉末粘附引起磨机堵塞。
A material: to strictly control the feed rate and feed temperature, maintain uniform feeding, but also reduce the material humidity, Raymond mill grinding material humidity must be below 6%, too wet material will cause clogging caused by adhesion of powder mill.
二、选粉机方面:要降低选粉机的转束,用来增大风机的进风量。
Two, select the powder machine: to reduce the rotating beam of the powder selection machine, used to increase the air intake of the fan.
三、磨盘和磨辊如果磨损严重要立即换新,如果因为间隙不当要适当的增大间隙。
Three, if you wear plate and immediately to the new grinding roll, if improper to increase the gap because the clearance is appropriate.
雷蒙磨粉机主机电流高是什么原因?主机电流高对磨机有什么影响?现在大家都知道了吧,客户朋友们在遇到这种情况的时候,不要着急,先停机,按照上面的原因一一排查,找到原因之后再进行解决。
The host of Raymond mill current high is what reason? What is the effect of the high current on the mill? Now we all know it, customer friends in the case of this situation, do not worry, first down, in accordance with the above reasons one by one investigation, to find the reasons for the solution.
雷蒙机 4R3220雷蒙磨粉机

相关资讯

  • 雷蒙磨技术参数的集尘和进气设置2019-10-11
  • 高压悬辊雷蒙磨粉机辊子的滚动可2019-10-11
  • 如果遇到雷蒙磨粉机的小批量生产2019-09-28
  • 雷蒙磨机进料辊间隙调节板的设计2019-09-28
  • 你知道雷蒙磨齿轮传动失败的原因2019-09-26
  • 在雨雪天气中,雷蒙磨粉机应该注2019-09-26
  • 雷蒙磨机残留空气管道的阻力决定2019-09-24
  • 雷蒙磨粉机的风量调节是决定成品2019-09-24

相关产品

  • 雷蒙磨粉机

    雷蒙磨粉机

  • 重晶石磨粉机

    重晶石磨粉机

  • 5R雷蒙磨粉机

    5R雷蒙磨粉机

  • 雷蒙机

    雷蒙机

  • 6R雷蒙磨粉机

    6R雷蒙磨粉机

  • 梯形磨粉机

    梯形磨粉机

  • 高压雷蒙磨

    高压雷蒙磨

  • 小型雷蒙机

    小型雷蒙机

?
XML 地图 | Sitemap 地图