资讯动态

新葡亰496net 企业概况 产品中心 资讯动态 成功案例 服务中心 联系大家

雷蒙磨维护大全你值得拥有


雷蒙磨磨粉过程中,用户要注意对机器的维护和保养,这样他会表现的更好。在磨粉过程中,如果维护保养不到位,将不能完全体现出其性能优势。但是,如果对它进行合适的保养,它的性能就会得到改善,然后使用效果会更好,使用寿命更长。
Raymond Mill powder in the process, the user should pay attention to machine maintenance and maintenance, so that he will be better. In the process of grinding, if maintenance is not in place, will not be able to fully reflect the performance advantage. However, if it is properly maintained, its performance will be improved, and then the use of the effect will be better, longer life.
雷蒙磨
在雷蒙磨的使用中,如果出料管道不畅或堵塞进料过快,会使磨粉机风口堵塞。如果与输送设备匹配不当,会造成出料管道风减弱或无风堵死。对于机器生产过程中出现的故障,大家要仔细进行筛选,待查出故障后,应先清通输送口,变更不匹配的输送设备,然后调整磨粉机的进料量,使设备正常运行。
In the use of Raymond mill, if the discharge pipe is blocked or clogged feeding too fast, will make the mill outlet plug. And if the transportation equipment, improper, will cause the discharge pipeline wind weakened or blocked wind. For the failure of the machine in the production process, we need to carefully screened, to find out the fault, should first clear the delivery port, transportation equipment, do not change, then adjust the feed mill, the normal operation of equipment.
在机器的使用中,如果锤片断、老化以及筛网孔封闭、破烂时,或者粉碎的物料含水量过高,都会使粉碎机堵塞。为了使得生产过程更顺利,用户要定期更新折断和严重老化的锤片,保持雷蒙磨的良好的工作状态,并定期检查筛网。在粉磨作业中,物料的含水量应低于14%,这样既可提高生产效率,又使磨粉机不堵塞,增强磨粉工作的可靠性。
In the use of the machine, if the hammer pieces, aging and screen hole closed, torn, or crushing the material moisture content is too high, will make the mill jam. In order to make the production process more smoothly, the user should be regularly updated and broken aging hammer, to maintain good working condition of Raymond mill, and regularly check the screen. In the grinding process, the material moisture content should be less than 14%, it can improve the production efficiency, and the mill is not blocked, to enhance the reliability of grinding work.
雷蒙磨在生产中,如果进料速度过快,导致负荷增大,造成机器的堵塞。所以,在进料过程中,用户要随时注意电流表指针偏转角度的变化,如果超过额定电流,表明电机超载。值得注意的是,如果电机长时间过载,会烧坏电机。这时,应马上减小或关闭料门,也可以改变进料的方式,通过增加喂料器来控制进料量。
In the production, if the feed rate is too fast, resulting in increased load, causing the machine to block. Therefore, in the feeding process, the user should always pay attention to the change of the angle of the current meter pointer deflection, if more than the rated current, indicating that the motor overload. It is worth noting that, if the motor overload a long time, will burn out the motor. At this time, should immediately reduce or close the discharge door, can also change the feed way, by increasing the feeder to control the feeding amount.
高压雷蒙磨
更多

相关资讯

更多

推荐产品

?
XML 地图 | Sitemap 地图